https://doi.org/10.4081/bse.176
Development of a multiscale testing method for the reduction of soft biological tissues waste during mechanical characterization
Published: 29 September 2021
Abstract Views: 657
PDF: 210
Publisher's note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
Authors
Two biaxial mechanical test methods were devised to compare their suitability for the mechanical characterization of soft biological tissues with the least possible tissue waste. Nanoindentation was used to explore the microscopic properties of the tissue and to overcome the macroscopic test limitations.
1. Negishi J, Hashimoto Y, Yamashita A, Zhang Y, Kimura T, Kishida A, Funamoto S. Evaluation of small-diameter vascular grafts reconstructed from decellularized aorta sheets. J Biomed Mater Res A 2017;105:1293-8.
2. Hiester ED, Sacks MS. Optimal bovine pericardial tissue selection sites. I. Fiber architecture and tissue thickness measurements. J Biomed Mater Res 1998;39:207–14.
3. Hiester ED, Sacks MS. Optimal bovine pericardial tissue selection sites. II. Cartographic analysis. J Biomed Mater Res 1998;39:215–221.
4. Billiar KL, Sacks MS. Biaxial mechanical properties of the natural and glutaraldehyde treated aortic valve cusp--Part I: Experimental results. J Biomech Eng 2000;122:23-30.
5. Sun W, Sacks MS, Sellaro TL, et al. Biaxial mechanical response of bioprosthetic heart valve biomaterials to high in-plane shear. ASME. J Biomech Eng 2003;125:372–80.
6. Sacks MS, Sun W. Multiaxial mechanical behavior of biological materials. Annu Rev Biomed Eng 2003;5:251-84.
2. Hiester ED, Sacks MS. Optimal bovine pericardial tissue selection sites. I. Fiber architecture and tissue thickness measurements. J Biomed Mater Res 1998;39:207–14.
3. Hiester ED, Sacks MS. Optimal bovine pericardial tissue selection sites. II. Cartographic analysis. J Biomed Mater Res 1998;39:215–221.
4. Billiar KL, Sacks MS. Biaxial mechanical properties of the natural and glutaraldehyde treated aortic valve cusp--Part I: Experimental results. J Biomech Eng 2000;122:23-30.
5. Sun W, Sacks MS, Sellaro TL, et al. Biaxial mechanical response of bioprosthetic heart valve biomaterials to high in-plane shear. ASME. J Biomech Eng 2003;125:372–80.
6. Sacks MS, Sun W. Multiaxial mechanical behavior of biological materials. Annu Rev Biomed Eng 2003;5:251-84.
How to Cite
Lugas, A. T., Serino, G., Terzini, M., Bignardi, C., & Audenino, A. L. (2021). Development of a multiscale testing method for the reduction of soft biological tissues waste during mechanical characterization. Biomedical Science and Engineering, 2(1). https://doi.org/10.4081/bse.176
PAGEPress has chosen to apply the Creative Commons Attribution NonCommercial 4.0 International License (CC BY-NC 4.0) to all manuscripts to be published.
Most read articles by the same author(s)
- Alessandra Aldieri, Mara Terzini, Diana Massai, Cristina Bignardi, Alberto Audenino, Development of an animal-free methodology for mechanical performance assessment of engineered skin substitutes , Biomedical Science and Engineering: Vol. 1 No. 1 (2020)
- Gianpaolo Serino, Andrea T. Lugas, Giacomo Bernava, Sara Ragazzini, Stefano Gabetti, Mara Terzini, Umberto Morbiducci, Alberto Audenino, Maurizio Pesce, Diana Massai, PDMS Substrates with tunable stiffness for cardiac mechanobiology investigation: A nanoindentation study , Biomedical Science and Engineering: Vol. 2 No. 1 (2021)
- Federico A. Bologna, Mara Terzini, Andrea T. Lugas, Alberto L. Audenino, Minimum performance level definition for bone plate testing according to standard: A preliminary study , Biomedical Science and Engineering: Vol. 2 No. 1 (2021)
- Simone Borrelli, Giovanni Putame, Mara Terzini, Andrea Ferro, Stefano Marone, Cristina Bignardi, Alberto L. Audenino, Total and local experimental validation of a lumbar spine numerical model to enhance the orthopaedic management of spinal metastases , Biomedical Science and Engineering: Vol. 2 No. 1 (2021)
Similar Articles
- Simone Borrelli, Giovanni Putame, Mara Terzini, Andrea Ferro, Stefano Marone, Cristina Bignardi, Alberto L. Audenino, Total and local experimental validation of a lumbar spine numerical model to enhance the orthopaedic management of spinal metastases , Biomedical Science and Engineering: Vol. 2 No. 1 (2021)
- Stefano Gabetti, Giovanni Putame, Federica Montrone, Giuseppe Isu, Anna Marsano, Alberto Audenino, Diana Massai, Versatile electrical stimulator for providing cardiac-like electrical impulses in vitro , Biomedical Science and Engineering: Vol. 1 No. 1 (2020)
- E. Marcello, G. P. Stola, C. Paoletti, L. Nicoletti, V. Chiono, Alginate dialdehyde-gelatin bioinks exploiting internal gelation mechanism for cardiac tissue engineering , Biomedical Science and Engineering: Vol. 4 No. 1 (2023)
- Eric A. Zizzi, Marco Cavaglià, Marco A. Deriu, Jack A. Tuszynski, In silico investigation of molecular interactions of volatile anesthetics: effects on phospholipid membranes and subcellular targets , Biomedical Science and Engineering: Vol. 2 No. 1 (2021)
- Licia Di Pietro, Alice Ravizza, Giovanni Vozzi, Andrés Diaz Lantada, Arti Ahluwalia, Carmelo De Maria, European regulatory framework for the clinical translation of bioprinted scaffolds and tissues , Biomedical Science and Engineering: Vol. 1 No. 1 (2020)
- Gianluca Ciardelli, On the transferability of tissue engineering technologies to the design of tissue models , Biomedical Science and Engineering: Vol. 1 No. 1 (2020)
- Irene Carmagnola, Tiziana Nardo, Francesca Boccafoschi, Valeria Chiono, Layer-by-layer coating of stainless steel plates mediated by surface priming treatment to improve antithrombogenic properties , Biomedical Science and Engineering: Vol. 1 No. 1 (2020)
- Gianvito Grasso, Lorenzo Pallante, Jack A. Tuszynski, Umberto Morbiducci, Marco A. Deriu, Computational molecular modelling as a platform for a deeper understanding of protein dynamics and rational drug design , Biomedical Science and Engineering: Vol. 1 No. 1 (2020)
- Susi Burgalassi, Erica Zucchetti, Eleonora Terreni, Daniela Monti, Silvia Tampucci, Patrizia Chetoni, Reconstituted epithelial corneal tissues for evaluation of drug delivery , Biomedical Science and Engineering: Vol. 1 No. 1 (2020)
- Monica Boffito, Arianna Grivet Brancot, Ornella Lima, Simona Bronco, Susanna Sartori, Gianluca Ciardelli, Injectable thermosensitive gels for the localized and controlled delivery of biomolecules in tissue engineering/regenerative medicine , Biomedical Science and Engineering: Vol. 1 No. 1 (2020)
You may also start an advanced similarity search for this article.
